8BVI0440HCSS.000-1 B&R Electronic Components

Product Details

• Weight4.3 kg
• Type
  EnDat 2.2
• Quantity
  2
• Peak current
  88 Aeff
• Max. output frequency
  598 Hz
• Max. extinction energy per switching operation
  3 Ws
• Output voltage
  24 VDC +5.8% / -0.5%
• Overvoltage category per EN 61800-5-1
  III
• Encoder monitoring
  Yes
• Certifications Functional safety
  Yes (openSAFETY)
• Output voltage DC bus voltage (UDC): 260 to 315 VDC
  25 VDC * (UDC/315)
• Encoder power supply Load capacity
  350 mA
• Permissible mounting orientations Horizontal, face up
  Yes
• Reduction of continuous current depending on switching frequency and mounting type Switching frequency 5 kHz Cold plate mounting
  0.8 A/K (starting at 45°C)
• Encoder power supply Protective measures Short-circuit proof
  Yes
• Cooling and mounting type
  Cold plate or pass-through mounting
• Connections
  9-pin female DSUB connector
• Modulation compared to ground potential
  Max. ±38 V
• Power dissipation depending on switching frequency Switching frequency 10 kHz
  [0.2 * IM² + 11.1 * IM + 130] W
• Installation elevation above sea level Maximum
  4000 m
Electrical isolation Input - Input
Yes
Protective measures Undervoltage monitoring
Yes
Dimensions Width
106.5 mm
Dimensions Depth Cold plate
212 mm
DC bus capacitance
990 µF
Power dissipation depending on switching frequency Switching frequency 20 kHz
[1.85 * IM² + 3.8 * IM + 300] W
Max. motor line length depending on switching frequency Switching frequency 5 kHz
25 m
Synchronous serial interface Data transfer rate
6.25 Mbit/s
Installation elevation above sea level Nominal
0 to 500 m
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 10 kHz Cold plate mounting
0.62 A/K (starting at 6°C)
Temperature Operation Maximum
55°C
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 20 kHz Cold plate mounting
0.32 A/K (starting at -82°C)
Dimensions Depth Pass-through mounting
209 mm
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 20 kHz Pass-through mounting
0.24 A/K (starting at -137°C)
Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves
0.5 to 16 mm²
Encoder power supply Protective measures Overload-proof
Yes
Terminal connection cross section Approbation data UL/C-UL-US
20 to 6
Temperature Operation Nominal
5 to 40°C
Terminal connection cross section Approbation data CSA
20 to 6
Variant
ACOPOSmulti backplane
Nominal switching frequency
5 kHz
Response threshold for open-circuit monitoring
Approx. 0.5 A
Degree of protection per EN 60529
IP20
Variant U, V, W, PE
Connector
Input voltage Maximum
30 VDC
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 10 kHz Pass-through mounting
0.37 A/K (starting at -36°C)
Max. power consumption
31 W + PSMC1 + PSLOT2 + P24 V Out + PHoldingBrake
Possible switching frequencies
5 / 10 / 20 kHz
Continuous current
4.2 A
Certifications EAC
Yes
Max. motor line length depending on switching frequency Switching frequency 20 kHz
25 m
Switching threshold High
>15 V
Electrical isolation Input - Inverter module
Yes
Dimensions Height
317 mm
Fuse protection
250 mA (slow-blow) electronic, automatic reset
Insulation stress of the connected motor per IEC TS 60034-25:2004
Limit value curve A
Pollution degree per EN 61800-5-1
2 (non-conductive pollution)
Certifications CE
Yes
Protective measures Overload and short-circuit protection
Yes
Permissible mounting orientations Standing horizontally
No
Continuous power consumption
32.5 kW
Response threshold for undervoltage monitoring
24 VDC -2% / -4%
Certifications KC
Yes
Relative humidity Transport
Max. 95% at 40°C
Slots for plug-in modules
2
Input capacitance
32.9 µF
Max. power consumption per encoder interface
PSMC[W] = 19 V * IEncoder[A]
Module width
2
Power dissipation depending on switching frequency Switching frequency 5 kHz
[0.07 * IM² + 7.3 * IM + 40] W
Variant Shield connection
Yes
Protective measures Open-circuit monitoring
Yes
Switching delay Rising edge
52 µs ±0.5 µs (digitally filtered)
Temperature Transport
-25 to 70°C
Input voltage
25 VDC ±1.6%
Continuous current per motor connection
44 Aeff
Terminal cable cross section dimension of shield connection
23 to 35 mm
Discharge capacitance
0.22 µF
Reduction of continuous current depending on installation elevation Starting at 500 m above sea level
4.4 Aeff per 1000 m
Encoder power supply Output voltage
Typ. 12.5 V
Synchronous serial interface Signal transmission
RS485
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 5 kHz Pass-through mounting
1.26 A/K (starting at 40°C)
B&R ID code
0xAA1F
Continuous power per motor connection
32 kW
Extinction potential
Approx. 30 V
Status indicators
UP/DN LEDs
Circuit
Sink
Output voltage DC bus voltage (UDC): 315 to 800 VDC
24 VDC ±6%
Protective measures Overload protection
Yes
Protective measures Short-circuit and ground fault protection
Yes
Input voltage Nominal
24 VDC
Switching threshold Low
<5 V
Relative humidity Operation
5 to 85%
Max. switching frequency
0.5 Hz
Input current at nominal voltage
Approx. 10 mA
Voltage Nominal
750 VDC
Relative humidity Storage
5 to 95%
Max. internal resistance
0.15 Ω
Max. motor line length depending on switching frequency Switching frequency 10 kHz
25 m
Switching delay Falling edge
53 µs ±0.5 µs (digitally filtered)
Permissible mounting orientations Hanging vertically
Yes
Max. encoder cable length
100 m ; Depends on the cross section of the power supply wires in the encoder cable
Certifications UL
cULus E225616; Power conversion equipment
Electrical isolation Encoder - ACOPOSmulti
No
Temperature Storage
-25 to 55°C

Related documents 8BVI0440HCSS.000-1 Specs